I’ll finish up the ending later and add instructions to convert decimal to hex. Next we will take the two last octets and convert those to hexadecimal.ġ00 becomes 64 in decimal, so add that to the MAC and it becomes 01-00-5E-40-64ġ becomes 1, add that to the MAC and we get our full MAC address 01-00-5E-40-64-01 Using the first 01-00-5E, we now add 40, which makes the MAC 01-00-5E-40. Now we use this for the next part of our MAC Address. So from our example, converting 64 to hexadecimal equals 40 or (0x40). You can use this website to automatically convert it for you: Decimals use a base 10 while Hexadecimals use a base 16. Using this method makes it much easier to work with large numbers over using decimal standard. You can think of it as though A is 10, B is 11, C is 12, D is 13, E is 14, and F is 15. Hexadecimal numbers use a base 16 where numbers are counted from 0 to 9 then letters A to F before adding another digit. Now that we have determined what the last seven bits of our second octet are we can convert it to hexadecimal. After dropping that first bit it changes the binary to 64 instead of 192! Do not skip this part. Had our multicast IP been 239.192.100.1, that would mean our binary would be 11000000. I could have explained this above but then you would have skipped through this part which does make a difference. Last 7 bits of 64 which still equals 64 converted to binary = 1000000Īfter removing 1 bit from our binary result it still equals 64 so this is what we will be using in the next step. Since we are only using the last 7 bits from the second octet, just drop the first 0 or 1 from our binary number (first binary number on the left, the result from 128 above). So above we converted the second octet of our multicast IP which was 64 to decimal which equal 01000000. Download tool here: Mag Converting Tool You also need this: JRE 1.8. now there is a way to get the line converted to an M3u line. You keep doing this until you can no longer subtract from the octet and you have converted decimal to binary. Hi Guys, We got a lot of people with an old Mac address line, People who bought directly from Rapid or from resellers who didnt transfer to the new dashboard. Can 64 be subtracted from 64? Yes, write a 1. Can 128 be subtracted from 64? No, write a 0. A quick way to do this is by following this example below. In the example I will be using the second octet of the multicast IP 239.64.100.1 which would be 64. The first step is to convert the second octet of the multicast IP to binary. You should have a good understanding of IP sub-netting or this may get a bit confusing.Ĭonvert Second Octet of Multicast IP to Binary To determine the rest of the MAC address we will use the remaining 23 low order bits to generate the full MAC address. The high order 25 bits of the MAC address are fixed and that is the 01-00-5E. As I explained above, any MAC address you see that starts with 01-00-5E is related to a multicast address. There is a specific range assigned for multicast, 01-00-5E-00-00-00 to 01-00-5E-7F-FF-FF for Ethernet and Fiber Distributed Data Interface (FDDI). I’ll explain below exactly how to determine the multicast MAC address from the multicast IP as well as provide a few helpful websites.Īt the layer 2 level whenever multicast is used it has to be assigned a MAC address in order to work. I knew that any mac address that started with 01-00-5E was a multicast address, but wasn’t sure how the rest of it was calculated. I am pretty sure that if I could assign this mac address to the helper vm the converter could access this machine in our network.Recently I was working to track down a multicast problem for a client on an enterprise network and needed to determine what the exact multicast MAC address would be. It seems to me that the Converter is trying to create this helper VM with a random Mac address but and I don't have control over that so that the logfile says "connect failed to ". In our company IP addresses are bound to MAC addresses, I already registered a new IP address with a VMWAre friendly (00:50:56:xx) Mac address in our IT department.īut when I use this IP address in the static helper VM setting in the Converter Standalone I am missing the information to enter a Mac address. Therefore I am trying to set up a static IP address for my helper VM machine but because I am within a enterprise network (which does not allow DHCP) I have the following problem. I want to convert a physical linux machine using the Converter Standalone 5.1. First, thank you all for this wonderful community, it helped me a lot in the past answering my questions by browsing the forums!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |